cutter plotter problem and Repairing.

follows are the different problem with cutting plotter and can not working to Repairing.....

Q: In the moment 1CM the following small print plotter Why deformed ?
A: The small print engraved spike compensation needs to be set in software . For example, in Wentai carving software : 1, click the " plotting output " plotting output picture will pop up ; 2 , click the "Settings" pop- carving machine settings screen ; 3 , click the " compensation settings " dialog pops up frame ; 4 , select " cusp compensation" required adjust the value to achieve the desired effect . Compensation values ​​between 0.1-0.7 , generally setting is 0.25. In addition, the cutting speed carving machine should be set to 20 words or less . Q: Why is the word engraved after cutting plotter will be more than a moment ?

A: 1, first check whether the upper and lower blade is not flexible ; 2, if some words are not normal , replace the carving software ; 3, check whether the document in question . Q: Why are there jagged cut when cutting plotter word ? A: Because the PUCT plotter motor drive power, high speed, so the cutting speed to be adjusted according to the size of the word set . Generally when cutting high precision , smooth fine print , the speed can not exceed 40. General cutting words , can speed 50-60 file. Cut characters, and the time when the number of multi- tight, available high-speed ( 70 , 180 ) , but a large step motor running , there will be significant sawtooth generator . Thus , the speed should be set according to specific circumstances . Relations font size and speed in the table below for reference : Font size (mm) SPEED ( speed ) <10 10-20 10-303030-50 40-5050-50060 > 50070-80.
Q: Why go plotter paper deviate when it drastically ? A: Place the paper roll in the paper feed tray to be completely parallel with the pressure roller adjustment for Large materials , lettering to relax in front of the roll , in order to avoid too much resistance when carving . For four pinch rollers of the machine, when the sharp carving back and forth repeating graphic , available only on the edge of two pressure wheels , can not be 4 while depressed , while uneven wear two wheels can also cause pressure paper deviate , serious need of replacement pressure roller .

Q: Why plotter plotting output will be " crash" ? A: 1, external 220V input voltage is too low (150V) , the plotter will restart and a " crash ." 2, the external 220V input voltage disturbances too , will crash , check the external 220V, the solution can be purified AC power supply. Q: Why plotter machine feels sometimes feel numb hand ? Answer : It is caused due to poor power supply ground , make sure the neutral grounded power source.

Q: Why would the word plotter cutting corners to provoke , not smooth ? A: 1, tip extending pocket too long , make the required adjustment . 2 , cutter wear, replace the cutter can be.

Q: Why Sometimes plotter to draw a line after the first in order to plotting output ? A: Because the last time carving a non- normal exit , the plotter memory is not cleared off the knife command. Solutions to turn off the power on again , re- plotting output .

Q: No LCD display or a small row of black blocks ? A: 1, if there is no display , the power may not work , check the power supply to work properly. 2 , showing black block check that the power supply voltage is normal ? If this does not solve , contact a service station .

Q: Why is cutting the word sometimes is not closed ? A: The eccentric plotter cutter knife , there is a bias value , thus cutting the word will not be closed. Solutions need to set the "closed compensation" in the software. For example, in Wentai software : 1, click the " plotting output " plotting output picture will pop up ; 2 , click the "Settings" screen plotter will pop up ; 3 , click the " compensation setting " pop-up dialog ; 4 select " closure compensation" to adjust the size of the desired value , you can achieve the desired effect , the general setting of 0.5 . Q: Why strokes clepsydra phenomenon lettering ? A: 1, check the machine beat the value is appropriate ; 2 , reinstall the operating software ; 3, check whether the flexible head down ; 4 , if the problem persists , contact the service center. Q: Why always in low power state ? A: Because the light sensor does not detect the front of the paper. Front paper loading paper should cover the light sensor hole (PAPER SENSOR), and then make an automatic test paper .

Q: Why is the word knife cutting deep , shallow knife ? A: Because PCUT plotter using advanced soft PVC material as the mat knives to protect the cutter . However, the use of time is too long, will produce a scratch pad of so uneven pad knives , there will be deep knife when cutting words , shallow knife phenomenon . Then replace the pressure knives can be. In less severe cases , according to section 3.2.2 tune good knife , the knife to increase the pressure ( about 120-150 ) , can temporarily solve the problem.

Q: When plotting output , plotter does not work how to do ? A: 1, check the plotter and computer connections are correct ; pickup plotter ( plotter ) is using the computer 's COM1 or COM2 serial communication , check the communication port of the computer and hardware settings access the communication port are the same. 2 , check whether cutting the word machine is online , that is the LCD window display ON LINE. 3, check whether the baud rate is 09600 plotter , specific methods of operation ( boot and press ONLINE --- MODE --- BAUD - to see whether the parameters are correct , if 19200 , press + to direct the 09600 reboot . 4 , check the carving set plotter software whether the series pickup ( Wentai select CTN series pickups carving masters select CREATION PCUT PRO Taiwan pickup plotter ).

Q: after cutting the word , exposing not down how sticky notes ? do Answer: 1 , the output should be tested before the knife , the pressure is adjusted to the appropriate size 2 , lettering knife used for too long , replace knife.

Q: What are engraved characters should pay attention Answer: ? 1, with narrow when format plotter engraved characters , the system software will automatically split pages , so you can be spliced ​​together into a multi-page large print , please note that the output width is set to be consistent with the use of sticky notes in width. Additionally, in plotting output when should widen pages can also be set from the seams . 2, with a wide machine engraved characters, especially when long pieces of characters, in lettering have to leave before the output of paper, sticky notes look at the degree of deviation , then according to the actual situation of the paper to go , put a few paragraphs long pieces of characters into output and avoid the paper side, causing waste material.

Q: how to care for the plotter Answer :PCUT series plotter all of Japan advanced oil-bearing, long-term operation without refueling. every day after work is completed with a soft brush to clean the dust . residual glue on the base of available alcohol. long run in dusty environments , the use of more than two years maintenance personnel should be clear dust inside the machine , such as carving reduced accuracy , but also to deal with moving parts for maintenance ( tightening and replacement of worn parts ).

Q: Why does the plotter sometimes out of control Answer: ? may be transported or use, the signal feedback line is bad, turn the machine plugged in all the lines can be , if not solved, please contact your local dealer or customer service center to ask : Why cutting the word machine downtime occurs Answer: ? this is due to the long length of vibration or in use , the temperature effect , the servo drive plate potential drift , there is often downtime.