MUTOH-8000 printer maintain and repairing
MUTOH-8000 printer maintain and repairing.
the MUTOH printer break down and show error message:
1 , when the printer runs out of ink prompts you for some time ( the machine will sound an alarm whistle , flute ~ ~ ~ ~ on the LCD screen and prompts Ink near and), should be promptly replaced. Information can also be understood ink (Ink stanus menu ) , when replacing the cartridge , the cartridge should be promptly removed after insertion of empty new ink cartridge from the machine's monitor to avoid ink flowing down the pipeline to generate the bubble , so the printer can not properly work, resulting in breakage and so on.
2 , a long time with an ink machine , when you need to replace another ink type, ink cleaning fluid corresponding menu operation according to the machine the machine ink supply system ( all the parts in contact with the ink ) cleaning Clean ( menu Head wash, see " common menu description " ) . Since a long time with an ink , the ink will produce a lot of ink in the inner wall of the pipe scale , only confirm the ink system is completely clean before using a new type of ink.
3 , the cleaning blade periodically and replace the waste ink absorber . Scraped clean sheet press machine operation menu accordingly ( press Wiper cleaning key, select Yes or No. When you select Yes, the car will automatically exit ink tank , press the Enter key after the completion of the cleaning can be ) , Please wash scratch films woven hairless scratch test piece ( Note : Please do not squeeze , to avoid damage to the blade deformation ) . Choose Yes or No operation when replacing the waste ink absorber with menu Tanki replacement.
4 , periodically clean the machine's surface and interior. In their daily work , you should avoid ink and thinner, benzene , alcohol and other active substances spilled on the surface or inside the machine , the surface layer is destroyed or get to spend the machine , electronic components damaged machine .
5 Blocking occurs when the nozzle needle or pin biased , please print head cleaning, appropriate conduct ( head cleaning button is pressed Head Cleaning, choose Yes or No) according to the machine menu operation. ( Note: The daily work , when the machine is not working , do not put ink nozzle positions of idle , this will cause the ink to dry and cause plug, if the machine suddenly loses power at work , place the car slowly push back ink tank , reset )
6 , when the need to replace the cutter proceed according to the machine 's menu (Cutter Exchange Options , select Yes or No).
7 , when the machine needs transportation , please fix the sprinklers and all parts may cause injury , replace the waste ink in the absorbing material , the level of the machine is placed in the box , the level of fixed machine shipped out .
8 , should be added to expand the memory to turn off the printer , unplug the printer connection cables and power cord, and by touching a metal part on the printer to release the body and electrostatic clothes.
Routine maintenance considerations
In order to extend the life of equipment, reduce the failure rate caused by abnormal use , the equipment for a long time in the best working condition, please promptly in strict accordance with the following description of the contents of the equipment maintenance and repair .
1, RT8000 photo machine is a very sophisticated equipment , so the impact of the external environment on the device is very important , it is recommended that you place the device in direct sunlight spacious , clean, relative humidity and temperature is more appropriate for the workplace.
( 1 ) work site area of at least fifteen square meters or more . ( Because RT8000 pictures of the body is very large, too small work space is bound to move equipment location often performed on paper , unloading paper, ink , cleaning and other work sites so often to move the body of the nozzle position and the device itself will influential addition pictorial machine itself has a lot of optical sensors , if the device in direct sunlight is bound to affect the normal operation of the photo machine . )
( 2 ) If the external environment dirty pictures of bar grating , ink car ferry and rail if contaminated with excessive dust , ink car ferry will aggravate the wear . After a small wheel wear , Mexican trucks during operation will produce a lot of noise , will also affect the printing image.
( 3 ) the external environment is preferably maintained at a relative humidity of 55-85 %. ( Too dry environment , the equipment is easy to produce static electricity , affect normal operation , so serious that it destroyed some of the circuit board chips ; domestic supplies under existing paper too dry environment is very easy Alice, Alice in use paper will often rubs sprinklers greatly reduce the life of the nozzle . overly humid environment , humid water vapor will corrode the electronic components inside the device . )
( 4 ) Operating ambient temperature is preferably maintained at 25-30 degrees Celsius. ( Low temperature , causes the ink on the paper discharge can not be absorbed is coated so that the ink deposited on the surface of the paper , the printing is poor . High ambient temperature will affect the cooling device , thereby affect the normal operation of the device. )
2 , ink sac : the ink sac is a white plastic material with metal filter inside the bladder . It is located inside the ink vehicle , above the nozzle. Its main function is to filter impurities in the ink , can not be cleaned to prevent clogging of the nozzle opening and severe ; side of the ink bag is a translucent film with a tension line of the ink can be sucked in the ink bag , the ink is supplied to the nozzle . So when the spray chart the course of a color ink ink off serious situations , often because the ink sac caused by clogged filters generally replace the ink off the ink sac to solve the problem .
3 , the blade : blade located below the ink vehicle , insert the blade stand in tow board. For scraping the residual ink nozzle surface , it is necessary to keep the cleaning nozzle of the cleaning blade , cleaning them frequently . For example, the first printing of the test strip , only blue ink head there is jam , the machine automatically after cleaning , call the test strip , blue nozzle is not blocked, there are other colors nozzle plug phenomenon , or blue nozzle plugging a change in position of the needle , when the wiper blade is likely to be caused because of the dirty block pin .
4 ink stacks : Located just below the ink vehicle. There are stacks of four ink ( six-color machine has six ) CAP cap corresponding to the four ( or six ) heads. Its main function is when the device does not work , the nozzle surface sealed to prevent surface drying caused by spray nozzle clogging . There are two in each CAP cap ink pad , often caused by the phenomenon of serial ink ink pad too dirty , so to clean them periodically . ( Generally two days cleaning time , cleaning is best to use a little better quality of tissues, after dip wet , gently dip the ink pad and clean . )
5, CR grating bar : at the top of the machine frame , there is a very fine small grid above it , the main role is to run the process of locating the ink vehicle role . Grating of Mexican trucks would be too dirty positioning allowed , there may be a fight figure ghosting or misplaced. We recommend that you gently wipe at least once a month .
6 tracks: There are four tracks on the machine frame , each track width of about one centimeter or so , rolling ink car ferry runs in the meantime, if the track will be increased wear dirty car ferry ink , the ink will wear after Ferry car running abnormal sound effects and the impact of the plot . So to clean after the first track , conditional customers with the best track in the weekly wipe , and then coated with a little sewing machine oil on its top , in order to play the role of lubrication to reduce friction and prolong the life of the ink vehicle ferries .
7 , electrostatic machine work normally large, ranging from not working properly , printing stops midway , or print garbled , weight will destroy the circuit board chips. To avoid static interference devices work , please install the standard requirements of the ground . ( With a two- square solid core copper wire , insulation pulled out at both ends , one end connected to the fixing screws and shelf pictures of the body , and the other end connected to the copper plate [ area of 150 cm2 or more , the thickness of one centimeter about . ] or coarse some copper, or a copper strip is then buried underground copper conductors such as the following one meter deep in moist soil , watering some of the brine , conditional Some customers also Isaac charcoal, then the soil buried hit real good . )
8 Note that the cartridge level , should be promptly added refilled . Note : Be sure to fill ink in the off or standby. ( As applied when the ink filling the ink will roll , produce large gas bubbles , if the machine during printing, the ink, the bubbles are along the conduit into the ink bag , so that the ink does not drop to the level of the ink bag , interruption caused by ink printing process . unnecessary losses. best ink down after about 30 minutes and then continue printing. )
9 ways to maximize the use of paper measured in situ test paper method . If this paper is Alice, can reduce the chance of paper rubs jets.
These are our summed up in the use and maintenance of equipment process some experience , I hope for your help. What better way and experience , please contact us if you are in the use and maintenance of equipment.
