cnc wood engraver problems manual.

follows is to let you see cnc wood engraver manual and see different problem solution.

cnc routers Engraving machine before installation considerations :

1 . Do not install this equipment during lightning or thunder , do not install power outlets in wet areas , do not touch uninsulated power lines .
2 . Machine operator must undergo a rigorous training process must pay attention to the safety of the operation and safety of the machine, and strictly follow the rules and to operate a computer cnc routers engraving machine.
3 . Power supply voltage requirements 210V-230V, if the power supply voltage instability or around high-power electrical equipment , be sure to select the power supply under the guidance of professional and technical personnel .
4 . cnc routers Engraving machine, control cabinet must be grounded cord, plug the data cable can not live .
5. Do not wear work gloves operator is best to wear protective goggles .
6. Machine body is steel gantry part of aerospace aluminum castings, relatively soft when mounting screws ( especially when the motor is installed sculpture ) Do not be too hard to slip wire.
7 . The tool must be installed and clamped , keeping knives sharp , blunt make carving decline in the quality of the motor overload .
8. Do not put your finger in the scope of work tool , not the engraving head removed for other purposes . Non- processed materials including stone white cotton .
9. Do not exceed the machining range , the length of time you want to cut off the power does not work when the machine is moving , there must be carried out under the guidance of professional presence .
10. If the machine abnormal situation, please refer to the troubleshooting chapter in the operating manual or contact your dealer to resolve ; avoid man-made damage .
Two . cnc routers Engraving machine installation
Warning: All operations must be powered down under operation ! ! !
1, the mechanical connection body and the control box ,
2, the control cable end to the machine body on the control box .
3 , the power cord is plugged into the machine body on the Chinese standard 220V power supply.
4 , the control box is connected to the computer , the data cord plugged into the control box of the data signal input port and the other end plugged into the computer .
5, the power cord plugged into the control box on the power , and the other end is plugged into a standard 220V power outlet.
6, the chisel through the collet chuck mounted on the lower end of the spindle . When first loaded knife into the hole in the spindle taper collets right size , then the tool into the chuck hole , using a random small wrench stuck spindle neck flat groove , so they can not rotate , then big wrench counter- clockwise tighten the screw spindle mother , put the tool firmly.
Three . Operational processes cnc routers engraving machine
1 , according to customer requirements and design requirements for typesetting in After calculating the correct path , the path to a different tool to save. Saved into different files.
2 , after checking the correct path in the path to the file opened in cnc routers engraving machine control system ( preview ) .
3 , fixed material , the definition of a good job of origin . Opened the spindle motor correct tune better number.
4 power , for machine operation .
Power 1 Turn the power switch , power indicator light, reset the machine first self-test operation , X, Y, Z, axis back to zero , then their run to the initial standby position ( initial machine origin ) .
2 Using a handheld controller , respectively, X, Y, Z axis adjustment of the starting point of the alignment work of engraving ( datum ) . Spindle speed, feed rate , respectively, make the appropriate selections , the cnc routers engraving machine is working a wait state.
Carving 1 . Edited documents to be engraved .
2 Open the file transfer , transfer files to the cnc routers engraving machine can automatically complete the engraving work files.
When the upper end of the file after the engraving , carving knife will automatically lift and run to the starting point of the work
Four . Fault Analysis and removal cnc routers engraving machine
An alarm malfunction
Overtravel alarm , which means that the machine during operation has reached its limit for the position , please check the following steps:
1 , the size of the graphic design process is beyond the scope .
2, check the motor shaft and screw machine cable is loose, if it is , please tighten the screws .
3, the machine and the computer is properly grounded.
4 , the current coordinate value exceeds the soft limit value range.
Second, overtravel alarm and lift
Overtravel , all axes are automatically set in motion to move the state , as long as has been holding down the arrow keys to manually restore the connection state of motion when the machine left limit position ( ie, away from the ultra- point switch ) when ready .
Note that the direction of movement when moving table , you must stay away from extreme positions .
Soft limit alarm needs to be cleared XYZ coordinate settings
Third, the non-alarm failure
1, repeat precision is not enough, according to the first second check .
2, the computer is running , the machine does not move, check the electrical box with a computer-controlled card connector is loose, if it is , seated, and tighten the screws.
3, the machine can not be found in the Homing signal , according to the first two checks. Mechanical origin proximity switch failure.
Fourth, output fault
1 does not output , check the computer and the control box is connected.
2 Open carving Manager settings where space is full , the managers do not delete the file.
3 signal cable connection is loose, carefully check each line is connected.
Fifth, carving failure
1 , whether the various parts of loose screws .
2 check their processing path is correct .
3 . Whether the file is too large ten million computer processing error.
4 change the spindle speed to adapt to different materials ( generally 8000-24000 )
! NOTE: CVT spindle used for 6000-24000 idling speed range can differ depending on the hardness of the material, processing quality requirements and the amount of feed size and other factors appropriate choice of speed , usually a hard material , a small amount of feed required . when the high-speed carving fine , under normal circumstances , do not crank up the speed , so as not to overload the motor .
5 , loosen the knife chuck, clamping the knife turn directions , put the knife being , so the object is not smooth carving .
if any other problem or any info you want to know , please contact with us