Laser cutter engraver problems service support
Laser cutter engraver problems service support.
1. laser engraving machine laser head does not light.
( 1 ) Press the operator panel ammeter test button to check the status view :
① not current: Check the laser power supply is turned on , power lines are loose or fall off , the signal cable is loose ;
② There are current: Check lens is broken , the light path is serious deviation ;
( 2 ) Check the water circulation system is normal :
① Water does not : check the pump is damaged or not energized ;
② through water : inlet check whether the outlet is reversed or broken pipes ;
( 3 ) can burst , to self, to send data does not shine ( check the computer settings are correct )
2 laser engraving machine engraved or not deep shades.
( 1) Check whether the smooth flow water system ( pipes bent or broken pipes ) ;
( 2 ) Check the focal length is normal ( recalibration ) ;
(3) whether the normal optical inspection ( recalibration ) ;
( 4) Check whether the paper plates spread too thick , the water is too much ( re- corrected ) ;
( 5 ) Check the beams are parallel ( adjust both sides of the belt ) ;
( 6 ) Check the lens is broken ( replacement ) ;
( 7 ) Check the lenses or laser tube transmitter is contaminated ( re-cleaning ) ;
( 8 ) Check the water temperature is higher than 30 ℃ ( replacing the circulating water ) ;
( 9 ) Check the laser head or focusing mirror is loose ( step up ) ;
( 10 ) laser current intensity required to achieve 8mA;
( 11 ) laser tube aging ( replacement ) ;
3 laser engraving machine is not properly reset.
Whether ( 1 ) Check the sensor James Gray , bad or damaged ( dust or wipe the sensor replacement ) ;
( 2 ) Check the conduction band of flexible cable is bad or damaged ( trim reseating or replacing data cable data cable ) ;
( 3 ) Check the ground contact is reliable or high-voltage lines are damaged ( re- grounding or replace high voltage )
( 4 ) Motor wire is bad.
4 . Clepsydra.
( 1 ) Initialization incorrect data has been sent ( corrected ) ;
( 2 ) reversed the order of operations ( re- export ) ;
( 3 ) static ( ground wire is off ) ;
5.cleaning Crochet dislocation, not closed.
( 1 ) the edited file is correct ( re-edit ) ;
( 2 ) the selected target is beyond the layout ( re-select ) ;
( 3 ) Check the software parameters are set correctly ( re-set ) ;
( 4 ) computer system is wrong ( re-install the operating system and software ) ;
( 5 ) Check the belt tension about whether consistent or rear belt is too loose ( belt intensify ) ;
( 6 ) Check the belt is slipping or sync * jump teeth ( stepping sync * or belt ) ;
( 6 ) Check the beam is parallel to ( re- adjusting belt around ) ;
6 computer can not output.
( 1 ) Check the software parameters are set properly ( re-set ) ;
( 2 ) whether the press positioning start engraving machine and then output ( re-export ) ;
(3) whether the prior inspection machine did not reset ( re- corrected ) ;
If ( 4 ) Check the serial output port is consistent with the software settings ( reset ) ;
( 5 ) The ground wire is reliable, whether static interference data lines ( re- ground ) ;
( 6 ) Replace the computer serial port output test ;
( 7 ) Re- install the software and re- set the test ;
( 8 ) to format the computer system disk to reinstall the software testing ;
( 9 ) motherboard serial damage to be repaired or replaced.
7 route can not be calculated.
Calculation methods ( 1 ) Check the settings are correct path ;
( 2 ) Check the graphics file format is correct ( re- corrected ) ;
( 3 ) removable software reinstalled and set ;
8 Computer FAQ
( 1 ) decreasing the font ( re- install the operating system ) ;
( 2 ) the amount of data is too large to calculate the laser path ( wait for some time or an increase in computer memory ) ;
( 3 ) calculate the path for a long time did not respond , restart the computer test .
