How to Operate Manual Cold Laminating Machine

How to Operate Cold Laminating Machine.

Mounting Machines such advertising device in our daily lives is mainly used for advertising photo film post-production products, due to the effect of the film is to make the product look more bright color, more visual impact. Therefore, the operator manually master methods of operation are cooked cold laminating machine is a very critical factor.
Its method of operation manual cold laminating machine is mainly divided into the following two major steps: 

First, adjust the pressure of the plastic shaft
1 Turn the machine on both sides of the regulator handle on the cabinet, the upper and lower shaft separation, will be ready to be mounted in the map and cold laminating film placed between two axes simultaneously, turn the regulator handle, so that the shaft is parallel downward move, when suddenly turning the regulator handle feel relaxed when said upper and lower shafts have been in contact with, then please do not continue down the pressure, just gently strip the regulator handle tight. If the pressure continues, it will produce a variant of the shaft, so that the operation failed.

2, the pressure is adjusted, the map and cold laminating film between two axes between the two axes from the exit. Ready for mounted film.

Second, laminating cold laminating film
1, framed small picture (less than 1.5 m length)
Will cut a good cold laminating film (should be slightly larger than the figure number) pushed between two axes (the film down, release paper below), the front end of the two-axis cold laminating film is pressed, the film and release paper apart, pull to the rear of the machine film, wrap the rolls, release paper flat on the work front panel, near the site of the shaft by hand Gently press release paper, release paper and try to make the film separation, will be mounted the diagram on the release paper straighten hand help level the top of the chart from the middle to both sides, turning machine, press evenly into the two rollers in Fig. Do not just push in the chart on both sides of the front parallel graph inadvertently pressed into the shaft, otherwise it is pressed into the shaft portion of the phenomenon will gradually appear wrinkled, causing failure. If you are not sure will be pressed into the shaft parallel figure, the available double-sided adhesive tape 1 cm wide (2-3 cm length) of the front three or four point graph paper to stick together and isolation, attention should first stick stick paste the middle and then gradually parallel to the sides.

2, mounting enlarge (1.5 m length and above)
When mounting 1.5 m above chart, the most important is to prevent deflection diagram and film. Just pressed into the shaft portion is not bad in the least bit, you can go through a length of time will hack away. Therefore, methods of operation must be done properly. First, put on a long shaft to enhance the production of the maximum upgrade level of diagram, followed by the cold laminating film and diagram overlap together, cold laminating film, the figure below (cold laminating film on a plastic surface, Figure front near by back release paper, roll into a cylinder, one end on a clean ground, or on the desktop poke Qi, hand pinch, do not let misplaced Figure film, cold laminating film with the same figure into two axes between the time must have caught a man in the rear of the machine to send over the previous figures and cold laminating film, to prevent loosening dislocation, try to put positive on the machine, Rotary flat, and then move down the shaft parallel to the pressure adjustment good (according to the previously mentioned adjustment method) to suppress cold laminating film and figure in order to ensure that by laminating the film does not produce skewed map and can turn the machine first, try to go again, but do not go off-axis as the test Walking found during deflection, should be re-operation., if not skewed, to stop the rotation at any one position, the end of the cold laminating film off to. use scissors to cut the release paper (be careful not to cut the film), and then to eversion to the other side, turn the machine shaft rotation, while constantly peeled off the release paper, laminating film is on the map, after the completion of the section above, and then turn the machine back the same way to the other side Figure also mounted paste film, laminating this reason this work is completed.

3, will have a good figure framed in laminating decorative panel
First, double-sided adhesive tape pasted To be mounted on the back of the cold laminating film map. Any kind of double-sided adhesive tape pasted above method with cold laminating film laminating two methods would have been a good stick figure on the double-sided adhesive decorative board, lifted up the shaft on the machine, the plate along with the diagram put between two axes, adjust the pressure (pressure adjustment pick a section) and then either end of the double-sided adhesive tape release paper folding kick back and cut the part, turn the machine so that the paper is peeled isolated decorative panel glued part. Then paste parts not turn to the other side of the axis of rotation of the machine and continue to release paper peeled off (the same method of making large image), it is stuck in the decorative panel....
                       Read More News