How does Laser engraver good carving glass ABS
Laser engraving and carving techniques of presentation glass and ABS.
1 .laser equipment carving materials: color plates (ABS)
Color plates is a sculpture dedicated to engineering plastics by two or more layers of a composite consisting of color, its size is usually 600 * 1200mm, also a small amount of brand specifications for the 600 * 900mm. U.S. POWMRK to stabilize the quality, variety is recognized as the best products. Color plate engraving finish is usually used for a variety of instructions signage and badges. In the color plates can be divided into machinery and laser with two categories, some of which can also be used for the characteristics of the mechanical plate laser engraving, laser engraving plate: surface color thin (0.1mm) laser plate is generally 1.3mm 0.8mm. Mechanical board is generally 1.5mm), our experience is: If the surface color of the board is very thin, generally can be laser engraved, such as surface color engraving thick can try twice.
Engraving: If using a laser plate engraving plate effect will be very good, there was a clear contrast and sharp edges. When using the surface of a thin plate engraving machine with laser effects board without much difference, a closer look might edge is not as clear as the laser plate. Users generally do not use the kind of mechanical surface thick plate, or we need to adjust the laser power was smaller, reusable sculpture have tried to clear the underside, the final results may not be very good. In contrast, a large color plates (such as on the blackboard), gray-scale image can be designed sculpture, engraving after a large number of color plates themselves may be some distortion, usable hot water heated by hand after the game.
Cutting.
Under normal circumstances, users will require you to cut a good color plates, this time as you are using a laser plate engraving in after its cut. Note that speed is not too slow, not a cut through, should be divided three or four times, so the cutting edge of the material out flat, no signs of thawing. When carving processing power should just bbs.wescn.com the benefits, should not be too large to avoid melting marks appear. If using a mechanical plate, it can only be cut to 50 percent of its depth, then hand off and then play sandpaper the edges polished, user if there is mechanical machine can be cut off in the mechanical machine, and then to the laser engraving machine.
Cleaning
After carving can use a damp cloth or alcohol to clean the surface. But note that, as the laser power is set too high when engraving, color plates attached to the surface may make it difficult to wipe a layer of soot.
Colouring
If users do not ask, you can use those outlets to show signs of different colors. To have to coloring the coloring area carved deeper, you can use acrylic paint or alkyd enamel, others may destroy the finish paint color plate surface.
2 .laser equipment carving materials: glass
The laser can be engraved on the glass surface, but not deep engraving depth and can not be cut. Frosting or crushed under the effect of the laser can be generally formed on a glass surface. Is usually the case the user wants frosting instead of crushing effect, this key depends on how the glass texture, hardness are the same.
Engraving: Glass engraving is usually difficult to control, in accordance with the following steps can make a relatively smooth surface matte effect: in the area to be painted sculpture of a little wash clean, cut down some piece slightly larger than the area to be engraved in newspapers or napkins , the paper completely soaked wet with water and squeeze out excess water, the wet paper on the engraving area paved do not have wrinkles. The glass on the engraving machine, engraving at the paper or wet state, and then remove the glass, remove the remaining paper, and then clean the glass surface. If necessary, gently polish with 3M's ScotchBrite glass surface.
Under normal circumstances, the laser power settings should be smaller, precision setting in 300dpi, engraving speed to be faster, you can try to use large-sized lens for carving.
Note: When using laser engraving leaded crystal should be doubly careful, leaded crystal with ordinary crystals have different coefficients of expansion, in the sculpture which may cause cracks or broken crystal. Power setting smaller to avoid this problem, but still should always guard in case rupture.
Cleaning
After carving can use a damp cloth to clean the surface. "
Color plates is a sculpture dedicated to engineering plastics by two or more layers of a composite consisting of color, its size is usually 600 * 1200mm, also a small amount of brand specifications for the 600 * 900mm. U.S. POWMRK to stabilize the quality, variety is recognized as the best products. Color plate engraving finish is usually used for a variety of instructions signage and badges. In the color plates can be divided into machinery and laser with two categories, some of which can also be used for the characteristics of the mechanical plate laser engraving, laser engraving plate: surface color thin (0.1mm) laser plate is generally 1.3mm 0.8mm. Mechanical board is generally 1.5mm), our experience is: If the surface color of the board is very thin, generally can be laser engraved, such as surface color engraving thick can try twice.
Engraving: If using a laser plate engraving plate effect will be very good, there was a clear contrast and sharp edges. When using the surface of a thin plate engraving machine with laser effects board without much difference, a closer look might edge is not as clear as the laser plate. Users generally do not use the kind of mechanical surface thick plate, or we need to adjust the laser power was smaller, reusable sculpture have tried to clear the underside, the final results may not be very good. In contrast, a large color plates (such as on the blackboard), gray-scale image can be designed sculpture, engraving after a large number of color plates themselves may be some distortion, usable hot water heated by hand after the game.
Cutting.
Under normal circumstances, users will require you to cut a good color plates, this time as you are using a laser plate engraving in after its cut. Note that speed is not too slow, not a cut through, should be divided three or four times, so the cutting edge of the material out flat, no signs of thawing. When carving processing power should just bbs.wescn.com the benefits, should not be too large to avoid melting marks appear. If using a mechanical plate, it can only be cut to 50 percent of its depth, then hand off and then play sandpaper the edges polished, user if there is mechanical machine can be cut off in the mechanical machine, and then to the laser engraving machine.
Cleaning
After carving can use a damp cloth or alcohol to clean the surface. But note that, as the laser power is set too high when engraving, color plates attached to the surface may make it difficult to wipe a layer of soot.
Colouring
If users do not ask, you can use those outlets to show signs of different colors. To have to coloring the coloring area carved deeper, you can use acrylic paint or alkyd enamel, others may destroy the finish paint color plate surface.
2 .laser equipment carving materials: glass
The laser can be engraved on the glass surface, but not deep engraving depth and can not be cut. Frosting or crushed under the effect of the laser can be generally formed on a glass surface. Is usually the case the user wants frosting instead of crushing effect, this key depends on how the glass texture, hardness are the same.
Engraving: Glass engraving is usually difficult to control, in accordance with the following steps can make a relatively smooth surface matte effect: in the area to be painted sculpture of a little wash clean, cut down some piece slightly larger than the area to be engraved in newspapers or napkins , the paper completely soaked wet with water and squeeze out excess water, the wet paper on the engraving area paved do not have wrinkles. The glass on the engraving machine, engraving at the paper or wet state, and then remove the glass, remove the remaining paper, and then clean the glass surface. If necessary, gently polish with 3M's ScotchBrite glass surface.
Under normal circumstances, the laser power settings should be smaller, precision setting in 300dpi, engraving speed to be faster, you can try to use large-sized lens for carving.
Note: When using laser engraving leaded crystal should be doubly careful, leaded crystal with ordinary crystals have different coefficients of expansion, in the sculpture which may cause cracks or broken crystal. Power setting smaller to avoid this problem, but still should always guard in case rupture.
Cleaning
After carving can use a damp cloth to clean the surface. "
