Eco solvent plotter problem Solutions
Eco solvent DX5 head printer problem solution.
1. playing off grid map when Mexico.Grating stolen goods, and need to use cotton swabs with water scrubbing from top to bottom grating dip should be cleaned several times more than wipe the water dry with a dry cotton swab.
2. can not recognize ink cartridges.
Decryption Casson had to be re-inserted as good, or bad decryption card.
3. playing figure dislocation.
(1) belt pulley rub cards, need to adjust the pulley. (2) servo motor breaks down, need to replace the servo motor. (3) copper rings dirty, and need to clean or replace the copper rings.
4. no ink nozzles.
(1) car plates fever, need to shut down the machine rest.
(2) electric shock led astray, and in need of replacement with an electric shock.
(3) nozzle plugging, and need to pump wash nozzle. (4) ink tube interface block, and need to unplug the plug several times more than you can. (5) nozzle interference, interchangeable nozzle position, and the use of paper towels with electric shock pads on between the nozzle and the check is interfering with that nozzle, replacement nozzle. (6) In case of four nozzles at the same time no ink, after the exclusion of interference is not out of ink nozzle car plates shall be broken.
5. measuring less than a paper .
(1) measuring device dirty paper, and need to use cotton swabs stick with water scrubbing.
(2) measuring device not installed paper is good, need to reinstall.
(3) measuring device out of paper, and in need of replacement of paper measuring device.
(4) car plate bad, in need of replacement.
6. playing figure to the side of the ramp edges.
(1) servo motor breaks down, need to replace the servo motor.
(2) grating sensor is dirty, and need to use cotton swabs dip of water scrubbing. Grating sensor is broken, in need of replacement.
7. turn left when you hit a small frame rack.
(1) grating sensor is dirty, and need to clean water.
(2) grating sensor is broken, in need of replacement.
(3) the data cable plugged not required to plug several times over.
8. frequent measurement of paper.
(1) into the paper sensor is dirty, needs cleaning.
(2) paper sensor not plugged into the motherboard connection or contact with the bad.
(3) into the paper sensor is broken, in need of replacement.
9. playing chart spray ink drops .
(1) the air nozzle did not draw a net, need to spend more times.
(2) ink tube interface fit is not good, to be re-inserted or replaced interface.
(3) nozzle leakage, the need to identify where the leaks and then sealed with glue.
10. playing surface maps fuzzy.
Electrostatic interference, (electrostatic safe voltage dog day or less)
11. playing off plan when the rules of ink .
(1) car plate instability.
(2) nozzle position wrong.
12. common English Baocuo.
(1) Internal ERROR shutdown Bad carriage paper sensor (car board or paper measuring devices not plugged poor contact)
(2) Internal ERROR shutdown Carriage Axis Failure (Electrical poor contact be re-inserted, or electrical damage)
(3) Internal ERROR shutdown CB LOLT 01RANGE LL: 0 (measuring device contact paper is not good, need to re-insert or replace the test paper container)
(4) IMP assoservice: unexpected REQ (into the paper sensor being exposed or damaged)
13. playing surface maps in the wrong size adjustment method .
Auxiliary Function menu, press Menu → → efficiency quasi-longitudinal axis of line drawings → change the default value of 83.82 and pay attention to figure long will the number increase, the number will be smaller and reduce the map (Note, changes to in order to change a decimal to change per mm 0.1 date) after the change must be saved.
14. photo machine initial .
Accessibility Menu → Services menu on the left of the fourth key → Press → Press → Press Clear 16753 password.
15. adjusting the display and language.
(1) display adjustment, press the right key to exit the fourth multi-press several times to ensure full exit, press the right button 4213 and then on the left of 2 or 4 keys transferred out.
(2) language adjustments, press the right key to exit the fourth to more than several times to ensure the full exit by the right side of 421 and then press the left key to bring up 2 or 4.
16. the computer port settings .
Open BOOS first select Inteyrated peyipherals select superio device and then select the parallel portmode (ECP) and press F10 to save the setting.
17. Montague printer installation .
In Montague file / printer configuration / installation Montague printer / ENCAD Novejet / Novejet850 / install the printer / Set the default printer on / off / set.
18. the new installation of sprinklers .
Before tearing off the seal with the 50-60 degree warm water about 20 minutes, in his 20-30ml ink injection nozzle, and then connecting pipe joints. And then the air pump nozzle inside the net, wipe clean and can be installed after the painting hit.
19. the operation note .
(1) A day to use sewing machine oil scrub rails.
(2) ink cartridges can not be at the end of more than a quarter can not be high and three quarters. (3) between the nozzle and the shock can not have Loumo band or water.
