How is a printer Prepared to printing data
eco solvent printer to prepared to send to print data.
Prepared to send
print data, I saw light has been flashing, but press the ONLINE button after
the device is still not print.
Reason: incorrect once enforced termination inkjet operation, while stopped Inkjet Printer, but there is still a part of the computer terminal residues play.Data sent to the inkjet printing machine and is stored in memory, but the opportunity to consider these data is invalid Inkjet refused to implement Printing operations, and making into the follow-up Printing jobs can not be carried out normally.
The right to terminate inkjet steps are: first, the termination of RIP software on your computer computing and output, and then terminate the printing on the device (device will automatically invalid data in the memory cleared).
Li: Solving this problem is to first end RIP software, the output of the computer (if you press the "cancel out" button, the output of the window or continue to exist, is quite normal, you can not ignore it), and then close the Printer power for more than 3 seconds and then boot, if the self-test after the lights are still flashing you need to re-close the device for more than 3 seconds and then reboot normally after this operation can be a normal print (computer the output window will automatically close).
Printing ink drops that occur during the phenomenon.
Reasons: 1. Vice ink tank on the air filter in the Filter wet, resulting in poor ventilation.
2. Nozzle surface dust, dirt and other fine wool, the ink emitted constantly on the accumulation of dirt to a certain degree will be dripping.
Dealing with: 1. To replace the air filter.
3. With cleaning fluid cleaning nozzle surface of the light box cloth and check whether there are two edges extra flash, if available lighter burned.
Print media width detection is not accurate.
Reasons: 1. Print media is not smooth, a bit arch.
2. Print media more transparent.
3. Print medium thick.
Dealing with: 1. To re-load the print media, and to ensure its smooth surface.
2. For print media with the opaque.
3. For print media with the thinner.
The rear paper-advance motor spinning.
Reason: the back of photoelectric sensors can not sense media, the print media presence.
Dealing with: 1. Check print media is exhausted.
2. Check whether it is because Flex incurred Daojuan of adhesion.
Feed motor never turn back.
Reasons: 1. Photoelectric sensor has always been sensitive to the media objects in existence.
2. Photoelectric sensor dielectric function is turned off.
Dealing with: 1. Check photoelectric sensor head or its reflection across the board whether there is dirt adhesion
2. Check whether the media automatically send and receive functions
Set to manual (MANUAL), or the motor switch is turned off.
Feed back the motor direction of rotation is incorrect, do not send anti-close.
Reason: Because different media, print side may be diametrically opposed, therefore, for the opposite side with the printing after the print media must promptly change the
What feed the direction of motor rotation.
Processing: TAKE-UP button press continued to 3 seconds to enter "TAKE UP MODE SET" (to send and receive mode settings) menu, and then modify
Rotation direction (CW or CCW).
Found in print media, printing process deviation.
Reasons: 1. Print media, the loading method is not correct.
2. Print media before and after the process of placing skew, resulting in both sides Shouli Bu.
Processing: 1. The correct way to load print media: first, to make the rear of media sensor does not work (will automatically send and receive feature is set to manual feed motor on or off the back of the switch), and then installed in the print media after the scroll rod fixation with the roll up and put equipment back, then the relaxed part of the print media and through the pressure of their front wheel, the operator in front of his hands on the device and appropriate to use the power of the average stretch pull-print media so that all the appropriate tension all around, and then others with the roller lever down to medium width of the test until the test has been completed, the first resumption of the rear the role of medium detection sensor, and then re-use the arrow keys to get out a medium in order to test media skew the situation, if more serious, if necessary deflection
According to the above method to re-load the media.
2. Before and after the media should be a natural droop, do not skew.
Press forward or backward arrow keys to print media and were unable to move smoothly, and noise.
Reasons: 1. Print media too.
2. Feed speed setting too fast.
Dealing with: 1. For some or narrower using thin print media.
2. Turn into USER → FEED menu will be SPEED value (factory default value is 4) down to 1 or 2.
Nose run when noise or rules of "pop and click" sound, and the rules of the screen there are vertical stripes depth interval.
Reason: incorrect once enforced termination inkjet operation, while stopped Inkjet Printer, but there is still a part of the computer terminal residues play.Data sent to the inkjet printing machine and is stored in memory, but the opportunity to consider these data is invalid Inkjet refused to implement Printing operations, and making into the follow-up Printing jobs can not be carried out normally.
The right to terminate inkjet steps are: first, the termination of RIP software on your computer computing and output, and then terminate the printing on the device (device will automatically invalid data in the memory cleared).
Li: Solving this problem is to first end RIP software, the output of the computer (if you press the "cancel out" button, the output of the window or continue to exist, is quite normal, you can not ignore it), and then close the Printer power for more than 3 seconds and then boot, if the self-test after the lights are still flashing you need to re-close the device for more than 3 seconds and then reboot normally after this operation can be a normal print (computer the output window will automatically close).
Printing ink drops that occur during the phenomenon.
Reasons: 1. Vice ink tank on the air filter in the Filter wet, resulting in poor ventilation.
2. Nozzle surface dust, dirt and other fine wool, the ink emitted constantly on the accumulation of dirt to a certain degree will be dripping.
Dealing with: 1. To replace the air filter.
3. With cleaning fluid cleaning nozzle surface of the light box cloth and check whether there are two edges extra flash, if available lighter burned.
Print media width detection is not accurate.
Reasons: 1. Print media is not smooth, a bit arch.
2. Print media more transparent.
3. Print medium thick.
Dealing with: 1. To re-load the print media, and to ensure its smooth surface.
2. For print media with the opaque.
3. For print media with the thinner.
The rear paper-advance motor spinning.
Reason: the back of photoelectric sensors can not sense media, the print media presence.
Dealing with: 1. Check print media is exhausted.
2. Check whether it is because Flex incurred Daojuan of adhesion.
Feed motor never turn back.
Reasons: 1. Photoelectric sensor has always been sensitive to the media objects in existence.
2. Photoelectric sensor dielectric function is turned off.
Dealing with: 1. Check photoelectric sensor head or its reflection across the board whether there is dirt adhesion
2. Check whether the media automatically send and receive functions
Set to manual (MANUAL), or the motor switch is turned off.
Feed back the motor direction of rotation is incorrect, do not send anti-close.
Reason: Because different media, print side may be diametrically opposed, therefore, for the opposite side with the printing after the print media must promptly change the
What feed the direction of motor rotation.
Processing: TAKE-UP button press continued to 3 seconds to enter "TAKE UP MODE SET" (to send and receive mode settings) menu, and then modify
Rotation direction (CW or CCW).
Found in print media, printing process deviation.
Reasons: 1. Print media, the loading method is not correct.
2. Print media before and after the process of placing skew, resulting in both sides Shouli Bu.
Processing: 1. The correct way to load print media: first, to make the rear of media sensor does not work (will automatically send and receive feature is set to manual feed motor on or off the back of the switch), and then installed in the print media after the scroll rod fixation with the roll up and put equipment back, then the relaxed part of the print media and through the pressure of their front wheel, the operator in front of his hands on the device and appropriate to use the power of the average stretch pull-print media so that all the appropriate tension all around, and then others with the roller lever down to medium width of the test until the test has been completed, the first resumption of the rear the role of medium detection sensor, and then re-use the arrow keys to get out a medium in order to test media skew the situation, if more serious, if necessary deflection
According to the above method to re-load the media.
2. Before and after the media should be a natural droop, do not skew.
Press forward or backward arrow keys to print media and were unable to move smoothly, and noise.
Reasons: 1. Print media too.
2. Feed speed setting too fast.
Dealing with: 1. For some or narrower using thin print media.
2. Turn into USER → FEED menu will be SPEED value (factory default value is 4) down to 1 or 2.
Nose run when noise or rules of "pop and click" sound, and the rules of the screen there are vertical stripes depth interval.
